JetNet
4706

JetNet 4706, the full managed industrial PoE switch, is the advanced version from the winner of Best Choice of Computex Taipei 2007 Award, the JetNet 3705/3705f. JetNet 4706 is designed for industrial PoE applications such as IP surveillance or wireless access points, where power source is not conveniently located. It supports intelligent PoE control and schedule management; each of the four PoE ports can be configured in a weekly schedule by hourly basis and PoE on/off can be remotely controlled via SNMP and Web. Compliant to IEEE 802.3af PoE standard, JetNet 4706 can deliver up to 25W power per port and 80W per unit (@60°C) by the forced powering mode.

Category:

JetNet 4706, the full managed industrial PoE switch, is the advanced version from the winner of Best Choice of Computex Taipei 2007 Award, the JetNet 3705/3705f. JetNet 4706 is designed for industrial PoE applications such as IP surveillance or wireless access points, where power source is not conveniently located. It supports intelligent PoE control and schedule management; each of the four PoE ports can be configured in a weekly schedule by hourly basis and PoE on/off can be remotely controlled via SNMP and Web. Compliant to IEEE 802.3af PoE standard, JetNet 4706 can deliver up to 25W power per port and 80W per unit (@60°C) by the forced powering mode.

The two uplink ports of JetNet 4706 series can be configured as Rapid Super Ring ports recovering network failure in less than 5ms, or RSTP ports integrating with other standard switches. Full network management features such as LLDP, JetView Pro i2NMS, SNMP v3, QoS, IGMP snooping v3, are all supported. If the powered device fails to respond after a pre-configured time interval, JetNet 4706 will reboot the powered device and continue to monitor the powered device in every pre-configured time interval. Simply put, the unmanaged powered devices can be managed through JetNet 4706. The award-winning IP31 rigid aluminum flat casing and wide operation temperature range ensure a reliable operation in mass transit vehicles, for outdoor usage, etc.

Easy PoE Configuration
The four PoE ports can be configured to enable, disable, or schedule PoE function by the web interface. The Power mode provides Standard mode for IEEE 802.3af PD, Manual mode for user configuration of the power limit to IEEE 802.3af standard PD, or Ultra mode for user configuration to perform at the 25W power limitation. After configuration, the real-time status of PoE is shown in web interface.

Forced Powering Mode
Korenix provides advanced forced powering control to deliver power to those non-standard PoE devices that cannot be detected as valid PDs. In the early days PoE products that were circulating the market prior to the ratification of PoE standard 802.3af did not comply with the current standard and did not support PD detection and classification. The PoE switch cannot recognized the PD, thus, it will not forward the power. The forced powering ability solves this problem and enables all your PDs.

PoE Port Scheduling
Korenix provides an hourly/weekly scheduling mechanism for advanced power control. Each PoE port can be configured as on/off by hourly basis. This feature meets economical power management, security, or customer-specific requirements.

  • 2-port 10/100 TX Ethernet and 4-port PoE / PoE-plus
  • DC48V input, 15.4W output for IEEE802.3af PoE IP camera
  • DC55V input, up to 25W output for IEEE802.3at PoE-plusPTZ/IR camera
  • 100W total power budget
  • QoS for prioritized video transmission
  • Optimized IGMP Query, snooping for one-to-many video transmission
  • Port-based VLAN for video traffic isolation
  • MSR guarantees network reliability, 5ms failure recovery
  • IP camera keep alive check and auto failure alarm, recovery
  • IP camera loss/failure alarm through DO, e-mail and SNMP trap
  • Redundant power inputs
  • IP31 rugged aluminum case with great heat dispersing
  • -40~60oC wide operating temperature model available (JetNet 4706-w)
Technology
Standard
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-T
IEEE 802.1p Class of Service
IEEE 802.3af Power Over Ethernet(PoE)
IEEE 802.3at High Power PoE
IEEE 802.3 Flow Control and Back-pressure
IEEE 802.1D Spanning Tree
IEEE 802.1w Rapid Spanning Tree
Performance
Switch Technology
Store and Forward Technology with 3.2Gbps wire-speed
non-blocking Switch Fabric
System Throughput
1.785Mpps
MAC Address
2000
Packet Buffer
Embedded 1Mbits shared buffer
Transfer performance
14,880pps for Ethernet and 148,800 for Fast Ethernet and transfer packet size from 64 to 1522Bytes
PoE Technology
End-Span wiring architecture
PD classification detection, class ID 0~3 follow IEEE802.3af standard, and 30W High power deliver procedures for class ID 4.
Pin assignment: V+ (RJ-45 Pin 4,5), V- (RJ-45 Pin 7,8), TX (RJ-45 Pin 1,2), RX (RJ-45 Pin 3,6)
Protection: Provides over-current protection by PD class ID
Management
Management interface
SNMP v1, v2c and v3, Web browser, JetView and CLI Management
Management Security
4 entries for web, telnet, SNMP management security
SNMP Trap
Provides Cold start, Warm start, Port event, Power event, Authentication failure, PoE trap and Korenix private trap for proprietary functions
SNMP MIB
RFC 1213 MIBII, RFC 1493 Bridge MIB, RFC 1757 RMON MIB, RFC 2674 VLAN MIB, RFC 1643 Ethernet like MIB, RFC1215 Trap MIB, RFC 3621 Power Ethernet MIB, Korenix Private MIB
Firmware upgrade
TFTP, Local file and JetView
System Log
1000 system entries for system or remote log server
Event Alarm Relay
1 1A @24V Dry Relay Contact output for port link down, PoE and System power events
Quality of Service
Quality of Service determined by port, Tag and IPv4 Type of Service
Class of Service
IEEE802.1p class of service, with 4 priority queue
DHCP
Supports DHCP Cilent and DHCP Server function with specified IP exclusion and MAC binding function
Timer
Supports Network Time Protocol (NTP) to synchronize time from NTP Server
VLAN
Port based VLAN
IGMP Snooping
Supports IGMP Snooping v1/v2/v3 and IGMP Query v1/v2
Network Redundancy
Supports Rapid Super Ring function for network redundancy with 5ms network recovery time; To inter-operate with other higher level switches, JetNet 4706 provides Dual Homing II technology to conform with RSTP protocol.
JetNet 4706 also comforms with IEEE802.1D 2004 edition for RSTP and STP standand protocoes
PoE Port Control
Supports user configuration for PoE enable, disable, or based on schedule
Power Limit Control
The control mode supports IEEE802.3af Standard, Manual and Ultra mode for 30W Hi-power. The maximum DC power delivery on each PoE port is 12.9W@DC 24V input or 30W @ DC55V input
PoE Scheduling Control:
Each PoE port can be activated and powered scheduling with different rule. It supports weekly schedule on hourly basis
IP Security
IP security to prevent unauthorized access
Port Security
Port security to assign authorized MAC to specifc port
Interface
Number of Ports
4 x 10/100Base-TX with PoE Injector
2 x 10/100Base-TX ports
1 x RS-232 Console
Connectors
10/100TX: RJ-45
Console: RJ-45
Power & Relay Alarm: 6-pin Terminal Block
Cable
10Base-T: 4-pair UTP/STP Cat. 3, 4, 5 cable,
EIA/TIA-568 100-ohm(100m)
100Base-TX: 4-pair UTP/STP Cat.5, Cat.5E/Cat.6 cable,
EIA/TIA-568 100-ohm(100m)
Rest Button
For system reboot and factory default setting
Diagnostic LED
Power LED: Power 1/Power 2 (Green)
Fast Ethernet Port 1~4: Link(Green)/
Activity (Green blinking),
PoE Powering (Yellow on), PoE Detect (Yellow blinking),
PoE Disable (Yellow off), PoE Powering failure (Yellow fast blinking)
Fast Ethernet Port 5,6: Link(Green) /Activity (Green blinking)
Alarm (Red): Port link down or power failure occurred
Power Requirements
System Power
Support positive or negative power system with DC 24~55V power input range and polarity reverse protection
Power Consumption
8 Watts @ 50V (Maximum) without PD loading
Mechanical
Installation
DIN-Rail mount or desktop or wall mount
Case
IP-31 grade aluminum metal case
Dimensions
46.5 mm (H) x 147.8 mm (W) x 136 mm (D) without DIN-rail clip
Weight
0.72 kg with package
0.65 kg without package
Environmental
Operating Temperature
-25°C~60°C
Operating Humidity
5% to 95% (Non-condensing)
Storage Temperature
-40 to 85°C
Storage Humidity
5% to 95% (Non-condensing)
Regulatory Approvals
EMI
FCC Class A; CE/EN55022:2003 Class A;
CE/EN61000-3-2:2001 Harmonic Test;
CE/EN61000-3-3:1995 Flicker test
EMS
EN61000-4-2:1998,ESD,EN61000-4-3:1998, RS,EN61000-4-4:1995, EFT
EN61000-4-5:1995, Surge,EN61000-4-6:1996, CS
Safety
CE/EN60950
Shock
IEC 60068-2-27
Free Fall
IEC 60068-2-32
Vibration
IEC 60068-2-6
MTBF
324,345 Hours, MIL-HDBK-217F GB standard
TOP
Chat us
1
Need Help?
Contact us
Welcome to Gigantika

If you have any questions regarding our products and solutions, please feel free to engage in a chat with us!